lamitated armrest bevel - an idea

Talk about musical instrument construction, setup and repair.

Moderators: kiwigeo, Jeremy D

Post Reply
Valben
Beefwood
Posts: 22
Joined: Fri Apr 13, 2018 3:16 pm

lamitated armrest bevel - an idea

Post by Valben » Mon May 21, 2018 1:15 pm

Hi All,
In the attached pic my idea of how to prepare a laminated stock for the armrest.
This idea uses all the cuttings from back & top plates, bend them (you can bend 4 strips at the time) and glue them stacked until the desired depth is achieved.
Using mostly the top material will reduce the overall weight but 2 or 3 strips of harder wood in the stack will increase the stability.
p.s - In the pic the strips are not yet glued, I will rearrange them alternating top & back wood before to proceed further :-)
Cheers
Attachments
IMG_20180520_141956.jpg
IMG_20180520_141950.jpg

User avatar
kiwigeo
Admin
Posts: 9346
Joined: Sat Sep 29, 2007 5:57 pm
Location: Adelaide, Sth Australia

Re: lamitated armrest bevel - an idea

Post by kiwigeo » Mon May 21, 2018 1:29 pm

What sort of glue do you plan to use? I'd probably be using epoxy resin (eg Techniglue) as it will fill in any gaps.
Martin

blackalex1952
Blackwood
Posts: 539
Joined: Tue Aug 27, 2013 6:36 pm
Location: North East Victoria

Re: lamitated armrest bevel - an idea

Post by blackalex1952 » Mon May 21, 2018 2:31 pm

Good idea. I would like to see a photo of the finished guitar sometime down the track. I make my 'solid' ie laminated liners by hand bending them to fit each other as accurately as possible, then line the inside of the guitar where the liners will sit with packing tape. Then I use hot hide glue to glue them together in situ clamping with 'pegs' for want of a better word...I use the ones available from Supercheap Auto...they are the same as the ones Stewmac sells I believe, and are readily available. After the glue dries I then remove the bindings and the tape (it has to be pretty low tac tape so there is no clean up of the tape glue to do so that the HHG will adhere to the sides). Then I run the liner's lower edge over a rounding over bit on a router table. After that, glue the bindings to the sides. This means a neat job if someone looks inside the instrument. That's what I would do with liners for an edge bevel. Not sure that epoxy is that important, to my mind if voids were an issue, then all liners would be glued that way. Also, if there happen to be alignment issues the HHG can be heated and the laminations can be corrected as HHG will restick to itself. I have found that the bottom edge of the laminated bindings done this way, ie glued in situ to the guitar sides, needs careful attention re alignment. One way around this, as a precaution, is to make the laminations deep enough for sanding on a flat plate along with the sanding on the top edge that happens when fitting the top to end up with the depth that is required on the finished instrument. Cheers! Ross
"Everything I say on the topic is based solely upon inexperience and assumption!"

User avatar
kiwigeo
Admin
Posts: 9346
Joined: Sat Sep 29, 2007 5:57 pm
Location: Adelaide, Sth Australia

Re: lamitated armrest bevel - an idea

Post by kiwigeo » Mon May 21, 2018 3:23 pm

Not sure if hide glue would be the best glue. Looking at the photo and the number of layers...you can see quite a few sizeable gaps. I use epoxy for the 3 layered solid linings and falcate bracing on my builds...epoxy is usually my choice where there's a high risk of gaps.

Something else I've just noticed....you'll need to address some way of preventing the layers from sliding over each other while the glue is setting.
Martin

Valben
Beefwood
Posts: 22
Joined: Fri Apr 13, 2018 3:16 pm

Re: lamitated armrest bevel - an idea

Post by Valben » Mon May 21, 2018 3:34 pm

I was planning to use titebond but I have considered the use of a 5 min epoxy. I do not have any experience with hide glue, except the bottled one which I do not think is a good idea anyhow.
Thanks for the suggestion, I will use the epoxy, it dries faster and will allow gluing 2 or 3 strips at the time allowing more precise alignment between the strips.
At the end I should be able to realize a 30x30mm square stock with the exact shape of the lower bout.
P.s. I will use one unglued strip in contact with the inside of the form as a spacer to compensate for the thickness of the side.
Cheers

User avatar
kiwigeo
Admin
Posts: 9346
Joined: Sat Sep 29, 2007 5:57 pm
Location: Adelaide, Sth Australia

Re: lamitated armrest bevel - an idea

Post by kiwigeo » Mon May 21, 2018 3:45 pm

I wouldn't use 5 minute epoxy...Ive found the quality of the Selly's and other quick epoxies not that great and if you need to do any unplanned adjustments you might find yourself in a bind. The 5 minute stuff also doesn't gap fill as well as the Techniglue. Carbatec stock Techniglue.
Valben wrote:
Mon May 21, 2018 3:34 pm
I was planning to use titebond but I have considered the use of a 5 min epoxy. I do not have any experience with hide glue, except the bottled one which I do not think is a good idea anyhow.
Thanks for the suggestion, I will use the epoxy, it dries faster and will allow gluing 2 or 3 strips at the time allowing more precise alignment between the strips.
At the end I should be able to realize a 30x30mm square stock with the exact shape of the lower bout.
P.s. I will use one unglued strip in contact with the inside of the form as a spacer to compensate for the thickness of the side.
Cheers
Martin

User avatar
Allen
Blackwood
Posts: 5038
Joined: Thu Oct 11, 2007 5:39 pm
Location: Cairns, Australia
Contact:

Re: lamitated armrest bevel - an idea

Post by Allen » Mon May 21, 2018 4:27 pm

So is your plan to shape the arm bevel and not laminate a veneer over it? So what you will see is a stack of laminations much like plywood? If that's the case, your laminations of that stack better be very good as they will be on display to everyone.

If your instead going to laminated a veneer over top of it as is customary, then there are lots better traditional ways of going about this. Far easier too in fact.
Allen R. McFarlen
https://www.brguitars.com
Facebook
Cairns, Australia

Valben
Beefwood
Posts: 22
Joined: Fri Apr 13, 2018 3:16 pm

Re: lamitated armrest bevel - an idea

Post by Valben » Mon May 21, 2018 6:03 pm

Thanks Allen, the idea is to leave the laminate as is but with the plan B of covering it with a veneer in case it won’t look nice. This is just an idea (from someone who has limited experience) to use the scrap pieces laying around. Anyhow I agree with you, a better solution is probably to start with a proper size blank ... much less work .

blackalex1952
Blackwood
Posts: 539
Joined: Tue Aug 27, 2013 6:36 pm
Location: North East Victoria

Re: lamitated armrest bevel - an idea

Post by blackalex1952 » Mon May 21, 2018 6:08 pm

Ive found the quality of the Selly's and other quick epoxies not that great and if you need to do any unplanned adjustments you might find yourself in a bind.
Bind is a good choice of word! Potential Dad Joke there!!! :mrgreen:
-Ross
"Everything I say on the topic is based solely upon inexperience and assumption!"

User avatar
Boe Jonamassa
Blackwood
Posts: 316
Joined: Fri Mar 02, 2012 11:14 am
Location: Jupiter

Re: lamitated armrest bevel - an idea

Post by Boe Jonamassa » Tue May 22, 2018 7:37 am

kiwigeo wrote:
Mon May 21, 2018 3:45 pm
I wouldn't use 5 minute epoxy...Ive found the quality of the Selly's and other quick epoxies not that great and if you need to do any unplanned adjustments you might find yourself in a bind. The 5 minute stuff also doesn't gap fill as well as the Techniglue. Carbatec stock Techniglue.
Valben wrote:
Mon May 21, 2018 3:34 pm
I was planning to use titebond but I have considered the use of a 5 min epoxy. I do not have any experience with hide glue, except the bottled one which I do not think is a good idea anyhow.
Thanks for the suggestion, I will use the epoxy, it dries faster and will allow gluing 2 or 3 strips at the time allowing more precise alignment between the strips.
At the end I should be able to realize a 30x30mm square stock with the exact shape of the lower bout.
P.s. I will use one unglued strip in contact with the inside of the form as a spacer to compensate for the thickness of the side.
Cheers
I am with Martin, don't use 5 minute epoxy. Get yourself some BoteCote or West Systems. I use BoteCote, and a 500ml bottle will last you a couple of years.

Col

Valben
Beefwood
Posts: 22
Joined: Fri Apr 13, 2018 3:16 pm

Re: lamitated armrest bevel - an idea

Post by Valben » Sat May 26, 2018 6:40 pm

Here the laminated block 😉 solid and very light.
Attachments
IMG_20180526_112637.jpg

Andos
Kauri
Posts: 30
Joined: Tue Apr 25, 2017 4:12 pm
Location: Taranaki

Re: lamitated armrest bevel - an idea

Post by Andos » Mon May 28, 2018 5:25 pm

Nice one bro - looking good.

Valben
Beefwood
Posts: 22
Joined: Fri Apr 13, 2018 3:16 pm

Re: lamitated armrest bevel - an idea

Post by Valben » Tue Jun 05, 2018 10:35 am

Rest bevel block glued in place and shaped.
Attachments
IMG_20180604_163127.jpg
IMG_20180604_163048.jpg

Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests