Opinions wanted on use of this Sitka top...

Talk about musical instrument construction, setup and repair.

Moderators: kiwigeo, Jeremy D

Post Reply
rangerdave1
Wandoo
Posts: 12
Joined: Wed Mar 13, 2019 12:30 pm

Opinions wanted on use of this Sitka top...

Post by rangerdave1 » Mon Sep 30, 2019 11:48 am

I purchase a bear claw Sitka Spruce top from eBay and when it arrived, I was a little disapointed because the growth lines are spread wide apart. From my understanding, the tighter the grain the better so I am a bit concerned if this is good enough top. It has a good ring when I tap on it but mostly concerned about it's stability long term .

And before anyone ask, I bought it because I thought it looked good.. probably should have looked at it closer.

I attached a few photos and seeking advice and opinions
Attachments
IMG_4730.JPG
IMG_4729.JPG
IMG_4728.JPG
IMG_4727.JPG

User avatar
kiwigeo
Admin
Posts: 10582
Joined: Sat Sep 29, 2007 5:57 pm
Location: Adelaide, Sth Australia

Re: Opinions wanted on use of this Sitka top...

Post by kiwigeo » Mon Sep 30, 2019 12:46 pm

I've got some red spruce that looks a lot like that top. Looks a bit scary but sounds ok.
Martin

User avatar
lamanoditrento
Blackwood
Posts: 585
Joined: Thu May 05, 2016 9:50 am

Re: Opinions wanted on use of this Sitka top...

Post by lamanoditrento » Mon Sep 30, 2019 1:07 pm

I had thought the association between tighter grain and strength is a misnomer and the only reason for tight grain it is purely aesthetic. So if you liked the look of it, I'd say use it.

You could test the modulus of elasticity to be sure for that particular piece.
Trent

User avatar
Allen
Blackwood
Posts: 5252
Joined: Thu Oct 11, 2007 5:39 pm
Location: Cairns, Australia
Contact:

Re: Opinions wanted on use of this Sitka top...

Post by Allen » Mon Sep 30, 2019 3:02 pm

I have plenty of soundboards that have wide grain spacing but so bloody stiff that I end up taking them thinner than others that would have narrower spacing.

Lots of my clients would pick that top because it looks like timber.
Allen R. McFarlen
https://www.brguitars.com
Facebook
Cairns, Australia

User avatar
kiwigeo
Admin
Posts: 10582
Joined: Sat Sep 29, 2007 5:57 pm
Location: Adelaide, Sth Australia

Re: Opinions wanted on use of this Sitka top...

Post by kiwigeo » Mon Sep 30, 2019 4:30 pm

Well I think the consensus is...go for it! :)
Martin

User avatar
Steve.Toscano
Blackwood
Posts: 489
Joined: Thu Feb 07, 2013 11:43 pm
Location: Port Stephens NSW

Re: Opinions wanted on use of this Sitka top...

Post by Steve.Toscano » Mon Sep 30, 2019 8:11 pm

I'd be more concerned about the bearclaw then the wide grain....
In my experience tops with heavy bearclaw tend to be less stiff along the grain then those without.

rangerdave1
Wandoo
Posts: 12
Joined: Wed Mar 13, 2019 12:30 pm

Re: Opinions wanted on use of this Sitka top...

Post by rangerdave1 » Mon Sep 30, 2019 9:36 pm

Thanks for the replies. I wont stress over the wide grain.

I wouldn't normally buy an expensive guitar with bear claw but being able to build my own for fun lets me experiment so when i found this top for reasonable money, I jumped on it.

yakka
Myrtle
Posts: 87
Joined: Fri Jul 17, 2015 5:49 pm

Re: Opinions wanted on use of this Sitka top...

Post by yakka » Tue Oct 01, 2019 1:38 pm


Post Reply

Who is online

Users browsing this forum: Google and 112 guests