Not being the best with metal, lack of tools mostly, while making my classical bridge using a jig I based off of one in the book I came up with a different way to machine the nut. It seems to work.
When I made the classical bridge jig I used the rails to make the well so the front edge is parallel to the rails. My bishop Cochran router base adjustment is .8 mm per turn. So 1/2 = .4 mm, 1/4 = .2 and 1/8 = .1. These are all positions that are easy to see.
I made a nut holder that was the same thickness as the fret board so that I could easily set the depth. I zeroed on the front of the nut and proceeded to cut each slot. I had one that string location that I needed to ease the router into the rails. But it came out ok and pretty accurate. I have them all a tad more compensated so that I can clean the leading edge.
A different Jig to machine compensated nuts.
-
- Blackwood
- Posts: 547
- Joined: Mon Jan 21, 2013 2:59 am
- Location: Seattle
- Contact:
- Trevor Gore
- Blackwood
- Posts: 1607
- Joined: Mon Jun 20, 2011 8:11 pm
Re: A different Jig to machine compensated nuts.
Innovative!
One can probably be made by re-purposing bits of a Strat bridge.
In the book I didn't detail how the adjustable compensated nut jig was made, but I did mine pretty much all with hand tools. The adjustable brass blocks are made from 3/8" brass bar, same stock as the bolt bar in the neck. Cut to length with a hacksaw, filed to size, drilled with a pillar drill and tapped M3 (1/8" would be close enough). The rest is made totally from 3/4" x 3/4" x 1/8" brass angle, just sawn and filed to suit. The screw that locks it all up is M5 (10-32 UNF or 3/16" BSF (or even W) is close enough for that. Brass will saw quite well with a standard wood blade on a bandsaw, if you take it easy.johnparchem wrote:Not being the best with metal, lack of tools mostly, while making my classical bridge using a jig I based off of one in the book I came up with a different way to machine the nut.
One can probably be made by re-purposing bits of a Strat bridge.
Fine classical and steel string guitars
Trevor Gore, Luthier. Australian hand made acoustic guitars, classical guitars; custom guitar design and build; guitar design instruction.
Trevor Gore, Luthier. Australian hand made acoustic guitars, classical guitars; custom guitar design and build; guitar design instruction.
-
- Blackwood
- Posts: 547
- Joined: Mon Jan 21, 2013 2:59 am
- Location: Seattle
- Contact:
Re: A different Jig to machine compensated nuts.
I have some 3/8" brass bar stock on order. So I will give it a go next guitar.
-
- Blackwood
- Posts: 547
- Joined: Mon Jan 21, 2013 2:59 am
- Location: Seattle
- Contact:
Re: A different Jig to machine compensated nuts.
Is there a standard part that can lock the adjustment screw in tight but still allow the screw to turn. I suppose some sort of bearing with a set screw. Maybe two nuts locked against each other and a nylon washer. Something tight but still allows the adjustment. I assume there is something like that in the jig to hold the screw while the adjustment is made.
- Trevor Gore
- Blackwood
- Posts: 1607
- Joined: Mon Jun 20, 2011 8:11 pm
Re: A different Jig to machine compensated nuts.
It's set up like a Strat bridge. There's a spring (spare part for said Strat bridge) between the "back bar" (which is just the angle part of the base that the adjustable blocks sit on) and the back of each block. Look very closely at Fig 21-18 and Fig 21-19 and you may be able to see the springs.
Fine classical and steel string guitars
Trevor Gore, Luthier. Australian hand made acoustic guitars, classical guitars; custom guitar design and build; guitar design instruction.
Trevor Gore, Luthier. Australian hand made acoustic guitars, classical guitars; custom guitar design and build; guitar design instruction.
-
- Blackwood
- Posts: 547
- Joined: Mon Jan 21, 2013 2:59 am
- Location: Seattle
- Contact:
Re: A different Jig to machine compensated nuts.
Thanks, I did check out my strat as well. So the spring gives enough push back to adjust and then you lock the whole stack with the side screw. I get it now. That is a lot simpler than I was thinking.
- Trevor Gore
- Blackwood
- Posts: 1607
- Joined: Mon Jun 20, 2011 8:11 pm
Re: A different Jig to machine compensated nuts.
I like simple!
Fine classical and steel string guitars
Trevor Gore, Luthier. Australian hand made acoustic guitars, classical guitars; custom guitar design and build; guitar design instruction.
Trevor Gore, Luthier. Australian hand made acoustic guitars, classical guitars; custom guitar design and build; guitar design instruction.
Who is online
Users browsing this forum: No registered users and 40 guests